• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, patio doors experience wear and tear that could result in locks that fail. There are a few simple steps you can follow to ensure the security of your uPVC door.

If it's resetting the lock or cleaning the mechanism for locking these simple fixes will help you make your home more secure.

Clean the Lock

patio sliding door repair doors are ideal for letting the outdoors in and keeping out the elements. However they could pose a security threat in the event that the lock isn't working properly. Over time, wear and tear, cold and hot weather dirt and debris can cause your patio door lock to become difficult to operate. With a little attention, you can make sure that your lock for your patio door always works in a proper manner.

It is important to first clean the patio door lock and all moving parts. This will help get rid of any dirt or coatings that could be preventing the lock from working effectively. Start by wiping down all the moving parts of your patio door's lock with a damp cloth, then employ a scouring pad or rough damp cloth to scrub any difficult-to-access areas of the door and frame that are covered in dirt. Then, wipe the entire lock with a dry cloth to remove any remaining dampness and allow it to air dry prior to applying it to the next time.

If your patio door uses pin-tumbler locks you can apply powdered Graphite to the key. You can also use a Teflon oil like WD-40 Multi Use Product. This type of lubricant is able to be applied quickly and will not disintegrate over time. If you're unable to locate the right lubricant for your needs, you could try using a pencil that has a thick tip. Place the pencil into the lock, then shake it to distribute the graphite.

The tracks for sliding patio door repairs patio doors also require regular maintenance to keep them free of dirt, dust and other debris. They are particularly susceptible to ice and snow, which can cause them to jam or bind, making it harder for your patio doors to open and close.

Tracks for sliding patio doors and rollers can be cleaned by removing damaged or dirty weather stripping and cleaning them before installing it. The rollers of patio sliding doors repair doors can be cleaned and sprayed with an oil that is nonstick.

Lubricate the moving parts

uPVC French doors, like sliding patios, operate with 3 to 4 or occasionally 5 points locking mechanisms. These include the handle and lock cylinder that is operated by the key. These doors also need maintenance, and specifically lubrication of the moving parts. This can be done with an oil that is thin (never WD40) and should be done every year.

If the hinges aren't causing the issue, it could be that the door isn't aligned. It could be rubbing or catching the hole of the strike plate in the frame. The solution is to take off the strike plate and then use an abrasive chisel, which will enlarge the mortise that it rests in. This allows the latch to sit correctly in the hole, tilt and slide patio door repairs also prevents getting caught or rubbing against the frame.

When the cylinder is out of the way, measure its width with a book or piece of wood that can fit into the gap of adjustment screw above the lock. The outer dimension is measured from the outside of door to the center of cylinder. The inner dimension is measured from the center adjustment screw to the end cylinder.

Check the Lock's Width

If your patio door latch is difficult to turn even after oiling and cleaning, it's possible that it's not aligned with the strike plate. Verify that the door is properly balanced and if the hinge screws are tight. In most instances, moving the strike plate upwards or downwards can solve the issue.

The latch may not engage properly if the strike of the lock is too small. In this case, you'll need to enlarge the hole with either a hammer or chisel, and then test the latch to make sure that it contacts the strike plate smoothly without rubbing against or landing on the frame of the door jamb.

Before you purchase a replacement lock, you should first determine the mortise type of lock you currently have. This can be done by taking a look at the faceplate of the lock and determining if it is square or round. Take a look at each screw hole in the existing lock and note the size. This information will assist you in finding an alternative lock that is of the same size and fits perfectly into your existing hole.

You'll need to locate the mortise lock and inspect it for any scratches, bends or other damage that needs to be repaired. A damaged or bent latch is more likely than one that's been used a lot to break. Replace the lock if you notice evidence of damage.

Once you've decided on the kind of lock replacement you require Now it's time to begin the actual repair. Remove the handle and spindle from the patio door, and then put in the new one. Start by installing the interior handle. Align it with the spindle and then secure it in place using the two bolts or screws. Install the exterior handle after the interior handle. After you've completed these steps, test the handles to make sure that they are able to open and close easily and that the latch works correctly with the strikeplate.

Check the Door's Strike

The strike plate and the door latch are two pieces that work together in order to secure the door. If they are not aligned properly and the latch isn't latching the door properly. Fortunately, the issue is often easy to fix.

Check the receiving holes of the strike plate to ensure they are free of obstructions such as dirt or plastic plugs. Release the screws that hold the strike plate. This will allow it to move vertically, but it will not be able to separate from the frame. Adjust the strike plate to align its holes for receiving with the latch hooks of the door latch. Once the strike plate is adjusted, tighten the screws and then test the door to determine if it shuts smoothly with the new adjustment.

These plates are difficult to reach for homeowners who have sliding patio doors. However they are crucial for locking and unlocking your door. The metal plates are typically placed on the top and bottom of the door jamb, which is where they are used to support the door's latch. The door latch slides into the strike plate to create an airtight seal when closed. If the strike plate is damaged, rusted, or not properly installed, it could stop the latch from locking the door securely.

A misalignment between the strike plate and latch is one common cause for the patio lock to not close or remain in place. This can be verified using the "lipstick" test. Rub some lipstick on the outside of the deadbolt and then cover it with masking tape. The lipstick will leave an impression when you shut the door. This will show you exactly where the latch connects to the strike plate. If the mark is too low or high it is possible to adjust the strike plate.

Sliding patio door repair company door locks help keep your home safe from burglars. If they're not working correctly, you should fix the problem quickly. Follow these simple steps to repair your patio door lock and restore it's functionality.