• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Patio Door Lock Repairs

Over time, wear and tear could cause lock malfunctions. There are a few easy steps you can follow to restore the security of your uPVC door.

These quick fixes can make your home safer, whether you realign the lock or clean the locking mechanism.

Clean the Lock

Patio doors are great for letting the outdoors inside and keeping the elements out. However, they can be risky for security if the lock doesn't work properly. Over time, wear and tear, cold and hot weather, dirt, and debris can cause your patio door lock to become difficult to operate. With a little attention you can ensure that your lock for your patio door always works in a proper manner.

It's important to first clean the patio door lock as well as all moving parts. This will help remove any dirt or coatings that might be hindering your lock from working correctly. Start by wiping the moving parts on your patio door lock with an aqueous cloth. Then you can use a scouring paper or a rough damp cloth to scrub the dirt-infested parts of the frame and door. Then, wipe the lock down with a dry towel to get rid of any moisture. Let it air dry before using it.

If your patio door uses a pin-tumbler latch You can apply powdered Graphite to the key. You can also use a Teflon lubricant such as WD-40 Multi Use Product. This type of lubricant is able to be applied quickly and will not disintegrate over time. If you're unable find the correct lubricant for your lock, make use of a pencil with a more of a thicker tip. Put the pencil into the lock and jiggle it around a bit to spread the graphite.

Regular maintenance is also necessary to keep the tracks of sliding patio doors free from dust, dirt and debris. These tracks can be especially susceptible to ice and snow which can cause them be stuck or jammed, making it harder for your patio doors to open and close.

Tracks for sliding patio doors and rollers can be cleaned by removing dirty or damaged weather stripping and then cleaning it, before replacing it. The same applies to patio door rollers which can be wiped down and sprayed with non-stick lubricant to help them move freely.

Lubricate the Moving Parts

upvc patio door repairs French Doors, similar to sliding patios, are operated with 3 to 4 or sometimes 5 points locking mechanisms. These include the handle and lock cylinder that is operated by a key. These doors also require maintenance, including lubrication of the moving parts. This can be accomplished with an oil that is thin but not WD40. It should be done at least once per year.

If the hinges aren't causing the issue, it could be that the door is misaligned. It could be rubbing against or catching the strike plate's opening in the frame. Remove the strike plate, and use a sharp tool to increase the size of the mortise. This will allow the latch to fit properly into the hole and also prevent it from scratching against the frame.

When the cylinder is out of the way take a measurement of its width using a book or piece of wood that fits into the gap between the adjustment screw and the lock. The outer dimension is the distance from the outside of the door to the center of the cylinder, and the inner measurement runs from the center of the adjustment screw to the end of the cylinder.

Verify the lock's width

If your patio door latch is difficult to turn even after oiling and cleaning, it's possible that it's not aligned with the strike plate. Check to see if the door is balanced and if the hinge screws are secure, but in many cases it is possible to move the strike plate upwards or downwards could fix the problem.

The latch may not engage properly in the event that the strike of the lock is too small. In this case you'll have to increase the hole with the hammer or chisel and then test the latch to ensure that it is able to engage the strike plate without rubbing against or catching on the frame of the door jamb.

Before you purchase a replacement lock, first identify the type of mortise lock you currently have. This can be done by looking at the faceplate of the lock and noting if it is round or square. Then, take a look at the screw holes on the current lock and note the dimensions of each one. This information will assist you in finding an alternative lock that is the same width and is a perfect fit for the hole that you already have.

You'll need to locate the mortise lock and examine it for scratches, bends or other damage that need to be repaired. A damaged or bent latch is more likely than one that's frequently used to break. Replace the lock if it shows evidence of damage.

After you've determined the type of lock replacement you require Now it's time to begin the actual repair. Remove the handle and spindle out of your patio door, and then insert the new one. Begin by installing the handle inside, aligning it with the spindle and then securing it by using the two screws or bolts that secure it. Once the handle's interior is in, install the handle that is outside and screw it into the position as well. After you've completed these steps check the handles to ensure that they are able to open and close easily and that the latch engages properly with the strikeplate.

Check the Strike of the Door.

The strike plate tilt and slide patio door repairs the door company latch are two components that work together to lock the door. Misaligned strike plate and door latches can result in the latch not being able to latch the door correctly. This issue is usually simple to repair.

Check the holes for receiving of the strike plate to make sure they are free of obstructions like dirt or plastic plugs. Loosen the keeper screws holding the strike plate in place. This allows it to move vertically, but not separate it from the frame. Then, adjust the strike plate to ensure that its holes for receiving are aligned with the latch hooks on the door latch. Once the strike plate has been adjusted then tighten all screws, and test whether the door closes smoothly.

Door strike plates can be a bit difficult to access for homeowners with sliding patio doors, but they're essential to lock and unlock your door. The metal plates are situated at the top and bottom jambs of the door, where they serve as the support for the latch. The door latch slides onto this strike plate and creates an airtight seal. If the strike plate is damaged, rusted, or not installed correctly, it may stop the latch from locking the door securely.

A misalignment between the latch and strike plate is the most common reason for the patio lock not to close or stay. This can be checked with the "lipstick" test. Apply some lipstick across the edge of the deadbolt and then cover it with masking tape. The lipstick will leave a mark when you close the door. This will reveal exactly where the latch meets the strike plate. If the mark is too high or low you can easily adjust the strike plate.

The sliding patio door locks keep your home safe from burglars. If they're not working correctly, you should repair the issue quickly. If you follow these steps, you can repair the lock on your patio door and regain its functionality within a short time.