• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Ignition Cylinder Lock Repair

The ignition cylinder lock allows the key to be turned in order for the car to start. It is controlled by a chamber with springs that may be damaged by environmental factors such as low or high temperatures.

If your ignition switch, key or both won't turn it could be an indication that the lock's cylinder has to be replaced. It is best to delegate the job to an expert automotive locksmith.

Take off the Steering Column Covers

Ignition lock cylinders are mechanical parts that allow a key to be put into the ignition switch and turned to turn on the car. They can wear out or malfunction in a variety of ways, including keys that are put in too hard or in the correct place. They can also degrade and fail due to corrosion or other causes. If your ignition cylinder isn't working and isn't turning, it's time to replace it. This is a straightforward task but you'll have to take off the steering column cover and the airbag cover. The process is dangerous and could be difficult. It may also require special tools for the replacement cylinder.

The ignition cylinder is located in the middle column where the steering wheel is positioned. It has two screws at the bottom and a clip on the side to secure it to the column. Remove these screws before you begin working on the cylinder to stop it from falling out and becoming lost.

After you have the screws removed, you can take the plastic retainers off the lower part of the cover. There's also a metal retainer that clips to the top of the cover to hold it in position. It is possible to remove the cover off of the steering wheel in order to take off the tabs on the lower part of the plastic.

The tabs can be ripped off by taking off one of the retaining screws and bending the tab outwards a little. If the tab is broken completely you can replace it with a perforated piece of strapping made of metal that is available at many hardware stores. You'll also need some U-clips for the new bottom "tab," and these can be bought from any auto parts store.

After removing the plastic tabs and pulling back the airbag cover, you can reach the ignition cylinder. With the 1/16-inch allen wrench, you can open the ignition lock and push it onto the cylinder retaining pin. Then, you can take the cylinder away. It may be necessary to replace it with a special one for an anti-theft system.

Take off the Ignition Cylinder

Although a majority of vehicles are now equipped with push-to-start, there remain some cars on the market that require an ignition lock. This cylindrical, mechanical component is located inside the electrically powered part called the ignition switch, which locks the ignition and "reads" anti-theft coding inside the car key so that it can start.

If your car is showing signs of a failing ignition lock cylinder, it might be time to call an auto locksmith for assistance. A damaged cylinder can lead to several problems, including a lack of power to the engine, as well as issues with inserting and removing the key. Keys that are damaged by wear can affect the wafer tumblers, which allow the ignition cylinder to rotate and create a blockage that stops your vehicle from starting.

Depending on the brand and model of your car, the ignition cover may be attached by screws or clips. With a screwdriver, loosen the screw, and then remove the cover to reveal the cylinder that locks the ignition. It is typically a steel cylindrical device about the size of a quarter.

To remove the cylinder, you'll need to remove the pin that holds it in place. Make use of a drill bit that is slightly larger than the slot that holds the key, and drill through it until the cylinder is broken. You'll then be able take the cylinder off and replace it with a replacement.

You'll need to refer to your service manual for exact steps to remove the ignition cylinder. Once the cylinder has been removed, you can install the new ignition switch.

First, you'll need to replace the steering column covers. Two screws are required to hold the lock assembly in place. Once you've done that, installing your new ignition cylinder should be fairly straightforward.

Remove the Ignition Switch

The ignition cylinder and switch are distinct components of the electrical system in your vehicle. Although they appear similar, the two are able to be repaired or replaced in a different manner from one other. The switch is electrical and provides the power to your vehicle. The cylinder is a mechanical tumbler that your key slides into. Generally, you can tell the ignition cylinder is failing because it is unable to turn your key.

If the cylinder fails, the pins in the tumbler may wear out, making it difficult or impossible to insert or pull your key. If you notice that your key is deteriorating and won't turn, it's best to have the wafers inside it replaced or smoothed out by an expert locksmith.

The ignition cylinder is exposed by taking off the bolt or screw depending on the model of the vehicle you're using. It is essential to check the manual for your vehicle before attempting this at home, as it can be dangerous and damage the steering column and plastic covers. The switch is also connected with the wiring for airbags. If you mess with it, it could cause serious injury.

To take the ignition cylinder out, you'll need to use an instrument to loosen it. It is also possible to use pliers however it's more difficult. After the ignition lock jammed cylinder is removed, you can purchase an alternative one at your local auto shop.

You'll need all the wires that are connected to the electrical connection on the steering column to test its operation. It's usually easiest to disconnect the battery first, then take the ignition key and start the engine. When the ignition is functioning, you can reconnect the battery and try it again. If your vehicle is still unable to turn on, you will require having the immobilizer reset. This can be accomplished by a dealer or an automotive service technician. This can be a complicated procedure, and is better left to a certified professional.

Install the Ignition Cylinder

The ignition switch in your car transmits a signal to the vehicle's engine that it's time to get started. The key is then inserted into a lock-cylinder to start this process. However the waxes and pins inside the cylinder could wear out over time. It could be difficult or impossible to start your vehicle if the cylinder becomes stuck.

If your car's ignition key doesn't turn, it's likely that the cylinder that controls ignition has worn out and requires replacement. A skilled locksmith can replace the cylinder with a new one, so the new key will work with the old ignition switch and will still be capable of activating the engine's startup signal.

To take out the old lock cylinder to remove it, push it into the release pin located at the bottom of the assembly, and slide the cylinder out from its housing. If the cylinder won't move out, try pressing the release pin or using a small anti-rotation button on the front of the cylinder. You can also push down on the cylinder while turning the key to the ACC position or accessory to force it out.

After you've removed the old cylinder, replace it with the new one and turn on the vehicle to check that it's working. If it is, you can connect the trim pieces you removed to connect to the cylinder. Then, you can go through an re-learning process to connect the new keys.

The lock for the ignition cylinder may not be as vital to the functioning of your car ignition switch replacement as it once was but there are situations that require you to replace it. Consult a professional such as an automotive dealer or locksmith to ensure the task is completed without damaging the steering column or other parts of your vehicle. It is essential to ensure that the new ignition is properly coded to ensure that your car recognizes it as an authentic key. In the majority of cases this, it will require a dealership or a professional to do the relearning.