• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A damaged or cracked window can be a source of frustration. It can also be a chance to upgrade your glass to energy-efficient or insulated replacement windows and doors and enjoy benefits such as more comfort, higher the value of resales and lower utility bills.

This is a project you could tackle yourself at only a fraction of the cost of hiring a professional. You only need the right tools and a few minutes of your time.

Glass

If your single-pane windows are outdated damaged, cracked or deteriorating replacing them with more modern glass that is tempered or insulated can increase energy efficiency and decrease noise while also preserving the original character of older homes. The procedure of replacing windows is easy and can be accomplished by most homeowners who possess basic hand tools. In addition to a new pane, the following items are required: latex glazing putty; pliers, glazier's points and the use of a heat gun to warm the old putty if required. Before starting, put on gloves and safety goggles as working with broken glass could cause injuries.

Take out any broken glass pieces that remain. This is best done using a pair of pliers, but a flathead screwdriver can also be used in a pinch. Then, use a wooden chisel or putty knife remove the remaining old putty around the frame and the sash. Take your time and work slowly and be careful not to damage the old window sash. It is recommended to do this using a sturdy ladder instead of the ground, and to place someone on the sash to help hold it steady.

Prepare the window frame to accommodate the new pane once you have removed the old putty. Measure the width and height of the sash opening, subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be sent to a home center or hardware store to have a piece cut of stock glass to the right size. Alternately, you can cut the glass yourself if you have the right tools.

After putting in the new glass, apply some caulking to the edge. This will make the glass weatherproof. Install a glazier's point on both sides of the frame. This will ensure the pane. The points shouldn't be too tight that they cause friction between the frame and the sash, but they should also not be loose.

Before applying the putty to the surface, you must knead it thoroughly until it becomes soft and free of lumps. Cut it into pencil-sized pieces. Apply the first strip to the corner of the frame. Work from corner to corner and ensure that it is even and smooth.

Glazier's Points

The glazier's facets are small triangular pieces that allow glass to be secured into a window frame without damaging or scratching the delicate surface. It's easy to learn how to use this secret tool and you can save money on the cost of an installation by a professional.

After removing the old putty, glazier points and any remnants, clean the frame thoroughly using a utility knife. If needed it is necessary to lightly sand the wood along rabbet grooves to smooth rough spots. If you decide to sand the wood, make sure to protect it with painter's tape to avoid accidental damage.

Measure the empty frame's dimensions and record precise measurements. Bring these measurements to a hardware store or home center, and have the new pane made slightly smaller than the frame's opening. This will ensure that the pane fits comfortably and allows for expansion and contraction.

Insert the new pane into the frame and press it down using your hands. Make use of the chisel's point, or the back of the putty blade to smudge the glazier's points as illustrated in Figure 11. The glazier's points should be aligned with the top edge of your pane and the shoulders should be just below that lip.

Apply a thin layer of glazing compound to the rabbet grooves as well as the edges of the glass. This will seal and protect the edges. Let it dry and cure completely.

Once the glazing compound has dried and the glazing compound is dry, you can install the new window sash. First, coat the wood with an even layer of linseed. This will keep the new putty from sucking in the moisture and deteriorating and cracking with time. Apply the coating using a brush this coat, or even the tip of the blade. Then, use the chisel that is on the back of the putty tool or the back of the putty handle to gently hammer the new replacement upvc window handles sash windows cost (This Web-site) or glazier's tip into the rabbet grooves. Repeat this process every 10 inches around the perimeter of the frame.

Putty

A baseball thrown at you, an errant rock or a falling branch can cause a window pane to crack or break. The majority of windows can be repaired easily by putting in a new piece. The glass is held in the position with a tiny metal clip, also known as the glazier's point, and putty. This compound is also known as glazing compound. Before you install a new pane, first take out the old one and clean the area using an abrasive and a pull-type paint scraper or the wood chisel. Wear gloves and safety glasses when you work. If the window is secured to the frame, you'll need to use a heat gun to soften the adhesive prior to prying it free.

If you're planning to install the original sash in the future, take care to remove the molding pieces that secure the old pane. Then you can sand the sash down to ensure it's level and ready for new caulk. After the sash has been re-installed then, apply a new caulk made of silicone around the glass to ensure it doesn't swell or fade as time passes.

Take out the glazing points in the rabbets. These are the grooves on the sash, which is where the glass is. If they're hard to chisel out, try holding the hand tool, such as a heat gun to soften them first. If you're using a heating gun, make sure not to cause damage to the railings of the sash or the sash itself by holding the tool too tightly.

Prepare a bed for your new pane after you have removed the old glaze and putty. Roll a piece of glazing compound between your hands, and form it into a 1/2-inch thick. Then, push it into the rabbets in which the glass will rest. It is crucial that the glass is positioned against the putty in all places on both sides If you have to, lightly tap the glass into the rabbet with your thumb.

If the new pane has a crack you can fill it with a solvent-based glue or silicone caulk before pressing it into the sash. If not, you'll have to apply putty on the crack to form a tight seal and keep water out. After the putty is dry and the film is oily, wipe it off the glass with a rag and allow it to dry completely before painting. Paint before the putty has dried completely. It will not create a solid seal and may leak or discolor with time.

Paint

If you've had a broken window pane, you might be concerned about the expense of a new one. The truth is, replacing a single piece of glass doesn't need to be expensive even if you do it your own. Even a double-paned window could be replaced for a fraction of what it will cost an expert.

First, if you're working on a large-sized window, make sure that it is securely fixed to the frame. With the right tools and techniques, you can accomplish this task fairly easily and speedy.

Once you're ready to begin with the removal of the old window pane by prying out the glazing points of metal that are attached to it. They are basically tiny metal triangles which function as "nails" that hold the window in place in the wood frame. They are buried beneath a bead or glazing glue which hardens into an unbreakable wedge that holds the wood frame securely in place and hides the points.

After removing the old pane, clean the frame and wood. Scrape away any old paint and sand down the rabbet grooves where the glazing points were. Sand them to bare wooden surfaces, allowing you to paint the frames with the same color. After sanding, apply a coat of flax oil to the wood that is not sanded down to help extend its lifespan.

Next, measure the dimensions of the window opening. You'll need to take horizontal and vertical measurements of the entire opening as well as the thickness of the old pane. To determine the exact dimensions of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass during seasonal change. Take these measurements to your local hardware or home improvement store, and they will have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.