• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane can be a nuisance. This can be an opportunity to upgrade your windows to energy efficient or insulated ones, and reap benefits like increased comfort, increased resale value and lower utility costs.

It's a task you can do yourself for a fraction of the cost of hiring a professional. It requires the right equipment and an hour or two of your time.

Glass

Replace your single-paned windows with tempered or insulate glass to improve the efficiency of your energy, reduce noise, and preserve the historical integrity of your old home. The process of replacing windows is simple and can be done by anyone with basic hand tools. You will also need an additional window pane, glazier's tips pliers, and latex glaze putty. If you need to you may use a heating gun to warm the old putty. Before beginning, wear gloves and safety glasses as working with broken glass may cause injuries.

Begin by removing any broken pieces of glass. It is recommended to use pliers for this however a flathead could be used equally. Then, use a wood chisel or putty knife to take the remainder of the old putty from the frame and sash. Work slowly and carefully, taking care not to break the current window sash. This can be done best on a ladder, not on the ground. Also, have someone lower to ensure it is held steady.

After you've removed all the old putty, prepare the window frame to fit the new pane. Measure the width and height of the opening for the sash, subtracting 1/8 inch from each measurement (to allow replacement handles for upvc windows seasonal expansion and contraction). These measurements can be taken to a hardware or home center store to get cut a piece of stock glass to the right size. You can cut the glass yourself if you have the appropriate tools.

After installing the new pane, run a small bead of caulking along the edge to make it weatherproof. Then, you can install a glazier's pointing on each side of the frame to hold the pane in the right place. The points shouldn't be too tight that they create friction between the frame and the sash However, they should not be loose.

Before applying the putty make sure to knead it until it is smooth and free of lumps. Roll it into pencil-sized strips. The first strip should be placed to the corner of the frame, working from one corner to the next so that it is smooth and even.

Glazier's Points

The glazier's facets are tiny triangular pieces of steel which help to secure glass into a window frame without scratching or damaging the delicate surface. Understanding how to use these hidden tiny pieces of help is simple and can save you money on professional installation or the cost of new replacement glass for window near me.

Once the old putty and glazier's points are removed, thoroughly clean the frame with a knife to remove any remaining residue. If needed it is necessary to lightly sand the wood in the grooves of the rabbets to smooth out rough spots. If you sand wood protect it with painter's tape to prevent accidental damage.

Measure the empty frame's dimensions and note down precise measurements. Take these measurements to an hardware store or home center and request that the new pane made slightly smaller than the frame's opening. This will ensure a tight fit and leave room for expansion and contraction.

Place the new pane into the frame and push firmly using your hands. Utilize the point of the chisel or the back of the putty blade to smudge the glazier's points, as shown in Figure 11. The glazier's points should sit in line with the top edge of the pane and the shoulders raised should be just below the lip.

Apply a thin layer of glazing compound on the rabbet grooves and the edges of new glass. This will protect and seal the edges. Let it dry and cure fully.

Install the new window sash after the glazing compound has dried. First, coat the wood with a thick layer of linseed. This will prevent the newly-created putty from drying out and cracking as it absorbs moisture. Apply this coat using a brush or the tip of your putty knife, then use the chisel or the back end of the knife to gently press the new sash and glazier's tips into the grooves of the rabbet. Repeat this procedure every 10 inches along the perimeter of the frame.

Putty

A baseball that is thrown or a rock that is errant or falling branch could cause a window to break or crack. Fortunately, the majority of windows glass replacement near me can be repaired by simply putting a brand new piece of glass in its the right place. The glass is held into position by a small metal clip, referred to as a glazier's point and putty. This compound is also referred to as glazing compound. Remove the old pane and clean the area using the rag, a scraper that is a pull type or a wood chisel. Wear protective glasses and gloves while you do this work. If the window is secured to the frame, you'll need use a heat gun to soften the adhesive prior to prying it free.

If you plan to reinstall the original sash, gently remove the molding pieces that secure the old pane. Sand the sash until it is flat and ready to receive new caulk. Once the sash is installed it is possible to apply a silicone caulk to the glass. This will ensure that it doesn't be leaking or fade over time.

Take the glazing points out of the rabbets and the grooves in the sash that the glass sits. If they are hard to cut, place the hand tool, like a heat gun over them to allow them to soften before. When using a heating tool, be careful to avoid damaging the sash and its railings.

Prepare a bed for your new pane after you have removed the old glaze points and putty. Roll a piece of glazing compound between your hands, forming it into a 1/2-inch thick. Then, you can press it into the rabbets, where the glass will be. It is essential that the glass rests against the putty in all places on both sides If you have to do so, gently tap the glass into the rabbet with your thumb.

If the new pane has damaged, you can use a silicone caulk or glass glue that is based on solvents to fill in the crack prior to pressing it into the sash. If the crack isn't sealed, you'll require putty to keep the water out. Once the putty is dry remove the oily film from the glass and allow it to dry completely before you paint. If you paint before the putty is completely dry, it won't form a solid seal and could discolor or leak in time.

Paint

If you've experienced a broken window pane, then you may be worried about the cost of replacing it. But the truth is that replacing one glass pane does not have to break the bank when you do it yourself. Even a double-paned window can be replaced at a fraction of the cost it will cost for a professional.

If you're working with a large glass window, first make sure it is securely attached to the frame. Using the proper tools and techniques, you can complete this task easily and speedy.

Once you're ready to begin with the removal of the old window by prying out the metal glazing points that are connected to it. These are tiny triangles of metal that act as "nails" that hold the window in place. They are buried under a bead of glazing putty, which is then cured to form a solid, formed wedge that holds the window firmly in place and conceals the edges.

After you have removed the old pane removed Clean up the frame and wood. Scrape away any old paint and sand down the rabbet grooves where the glazing points used to be. Sand them down to bare wooden surfaces so you can paint the frames the same color. After sanding, apply a layer of flax oil to the wood that is not sanded down to prolong its life.

The next step is to determine the width of the window's opening. You will need to take vertical and horizontal measurements of the entire opening and also the thickness of the old pane. Subtract 1/8 inch from each measurement to ensure that you have the exact size for the new pane. This will also allow for expansion and contraction of the glass during seasons of changes. You can take these measurements to a hardware store or home improvement store and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.