• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen work from high above the ground, moving huge panes of glass. They adhere to strict safety standards and are often working in harsh weather conditions.

Wearing protective clothing, take off the metal glazing points and all glazing putty with an utility knife. A heat gun will help soften and remove the old putty.

Replacement

It is tempting to fix the glass on your windows instead of replacing it if panes break. It is more cost-effective to replace a window, and it can also help to avoid other issues in the efficiency of your home. You should also take into consideration the kind of glass that is damaged to determine if it is a temporary fix or if you'll require a more permanent solution.

The first step in repairing broken windows is to take off the frame, or sash and place it flat on a table. While wearing eye protection, gently wiggle and pull out any shards that remain within the window. Use a utility blade to remove the glazing compound, and the glazing points that keep the window in place. Keep an eye on the location of these components to ensure that they can be reinstalled later.

After the frame and sash have been removed and the frame is removed, you can begin preparation to install new glass. Before you begin make sure that the opening in the frame is properly sized for your replacement window. To allow for expansion and contraction of the glass and frame and contraction take measurements in both directions across the opening and subtract 1/8 inch. Afterwards, purchase double-strength glass cut to these exact dimensions. It is also a good idea to purchase enough new glazier's glazier's pointing or clips to be positioned every 6 inches around the window pane.

Depending on the window's warranty the window may be covered by the manufacturer and in this case, you need to contact the company to file an claim. After the new glass has been erected it is crucial to cover it with a thin layer of glaziers compound. After drying the compound, you can paint it to match the rest of the window frame.

If your crack is more than an inch in length, you can prevent it from expanding by scoring an arc that is just a little beyond the crack. This technique isn't 100% foolproof but it will slow down the development of the crack until you can take more permanent measures.

Repair

Professional window contractors are equipped with the appropriate tools and know how to work with different types of glass. They know how to dispose of waste properly and are therefore less likely than other people to leave behind a mess which could cause harm to family pets or family members. They are also familiar with working with different types of windows, and may be able spot problems that an inexperienced home owner might not be able to notice.

Wear safety goggles and gloves prior to starting the process of repairing cracked glass. A minor crack could cause shards of glass to fly away, creating a risk for anyone living in or around the home. It is also crucial to determine the cause of the crack in the first place, so that it can help prevent future issues.

Create a two-part mixture of epoxy. They usually consist of composed of a 50/50 blend of hardener and resin. They must be mixed quickly. After the mix has been made and applied, simply apply it to the crack and allow it to dry. This should only take some minutes but it's important to get it done quickly as the mixture is extremely thick and quick drying.

Once the epoxy is dried, you can get rid of any excess using a putty knife. You'll need to clean the cracks in the glass. If you don't do it correctly, the resulting residue could cause further damage to the glass. Use a putty blade smooth the compound around the edge of the window and then match it to the frame made of wood.

For a more durable solution think about using a plastic cover. A heavy-duty trash bag or tarp is the best option, but you can also use masking tape to cover the glass. This will prevent the crack from spreading and will also keep water, wind and bugs out.

You can make a temporary fix when you are unable access the window in an efficient manner. Apply a small amount of silicone sealant on the edge of the broken glass. It won't completely seal the gap between frame and glass but it will help keep the break in place while you repair it.

Repainting

Repainting old glass windows is a good idea. This is a cost-effective alternative to replacing your windows and will give your home a fresh appearance. Make sure the window is clean before painting. Use soap or rubbing alcohol and water to wash away oil smudges, and other residues that could prevent paint from adhering. Wear rubber gloves when working on glass surfaces to avoid the transfer of oils from your hands onto the surface. Apply several thin coats instead of a single thick one. This will make the paint last longer, and keep your windows looking smooth and even.

If you're planning to repaint your glass windows, be sure you have all the right tools nearby. You will need either a brush or sponge painter's tap, a ruler and toothpicks. You'll need the paints and brushes that you will be using on hand. Make sure you adhere to the manufacturer's guidelines and be prepared with plenty of patience as it can take awhile for the paint to dry.

If you're using solvent-based paint, make sure that the area in which you work is well-ventilated. This will decrease the risk of breathing in toxic chemicals and permit the paint to dry more quickly. It is also important to ensure you have a mask to protect yourself for any spray paints that you use.

For older glass windows, it is necessary to prepare the surface before painting. Clean the glass thoroughly with soap and warm water, then use rubbing alcohol to clean off any grease or oil that could affect the adhesion of the paint. Make sure the windows are completely dry before you begin painting them.

If your glass windows are energy efficient dual pane windows, you might be in a position to file a claim with the dealer or window company that sold them to cover any repair or replacement costs. This is especially true if the windows are still under warranty and you've had numerous problems with condensation or damaged glass.

Sealing

If you have double-pane windows with a damaged seal or more recent insulated glass units (IGUs) that have experienced defogging and fogging, there are a variety of options to fix the issue. It is the most expensive option to replace the insulated unit as well as the frame. However, it may be required in situations where fog or condensation is causing energy loss. Other options include replacing the IGU with a single pane or repairing it by drilling a small hole into the bottom of the unit, and then filling the solution with anti-fog.

You can also fill in the gap between a window frame and a sill or threshold with a felt strip or vinyl V-strip. Felt is inexpensive and can be glued, nailed, or stapled into place however it doesn't offer much protection against moisture. Vinyl v-strip is easy to install and durable however it can be expensive. It is generally reserved for areas that are subject to high abrasion. Door sweeps are inexpensive and can be nailed to the floor but they create little to no barrier between the threshold or sill and air, dust, and other debris.

To repair a damaged window seal make use of a putty blade to take off the caulk. Wearing gloves and eye protection take out the glazing point -- small fasteners with sharp, pointed tips that pin the glass in the recess of the frame. After removing the glazing points, clean the grooves, then sand the wood. Clean any sanding residue, then seal the bare wood using a linseed oil-based paint or clear wood sealer.

Traditional glazing putty can be applied with a putty knife or caulking gun, however the knife is a better precision and precise application. It also provides a stronger seal. Choose a putty that is specifically designed for glass as it is more durable and stick better.

Apply a thin layer of putty on the inside of the frame where it meets with the glass. Slide the upvc window repair into the frame in a way that the scribed line on the glass is aligned with the edge of the frame. Apply pressure on the glass to compress the putty and glass to form an elongated seal. Smooth the compound using an ungloved finger, and wipe away any caulk that was applied incorrectly or spills that are not properly wiped away prior to drying.