• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane can be a nuisance. It could also be an opportunity to upgrade your Glass replacement on windows to energy-efficient or insulated windows, and benefit from greater comfort, a higher resale value and reduced utility costs.

You can do it yourself for less than what it would cost to employ an expert. It requires the right tools and an hour or two of your time.

Glass

Replace your single-paned windows using tempered or insulated glass to increase energy efficiency, reduce noise, and protect the original character of your old home. The majority of homeowners with basic hand tools can replace a window pane. Alongside a replacement window glass near me pane, the following tools are required: latex glazing putty; pliers, glazier's points and a heat gun for warming the old putty if required. Wear safety glasses and gloves before you begin. Working with broken glass could cause serious injuries.

Begin by removing any remaining broken pieces of glass. This is best done using the help of pliers though using flathead screwdrivers can work in the pinch. Make use of a wood chisel or putty knives, to take away any remaining old putty around the frame and the window sash. Be careful to not scratch the window sash. Be careful and slow. This can be done best on an elevated ladder, not on the ground. Also, ensure that someone below the sash hold it steady.

Make sure that the window frame is ready to receive the new pane when you have removed the old glue. Find the width and the height of the sash opening and subtract 1/8 inch from each measurement (to allow for seasonal expansion and contraction). Take these measurements to an hardware store or home center, and have a piece of stock glass cut to size. You can cut the glass yourself if you possess the appropriate tools.

After putting in the new glass After installing the glass, apply caulking on the edges. This will make the glass weatherproof. Install a glazier's point on both sides of the frame. This will help secure the pane. The points shouldn't be too tight that they create friction between the sash and frame, but they also shouldn't be loose.

Before applying the putty knead it thoroughly until it's soft and free of lumps. Roll it into pencil-sized strips. The first strip should be glued to the corner of the frame. Work from corner to corner, making sure it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of metal that allow glass to be secured into the window frame without causing any damage to the fragile surface. It's simple to learn how to use this hidden tool and you can save money on the expense of an installation by a professional.

After the old putty as well as the glazier's points have been removed Clean the frame thoroughly with a knife to eliminate any remaining residue. Lightly sand the frame in the rabbet grooves if needed to smooth out rough areas. If you decide to sand the wood, ensure you protect it by using painter's tape to prevent accidental damage.

Measure the empty frame's dimensions and record precise measurements. Take these measurements to an hardware store or home center and have the new pane made slightly smaller than the frame's opening. This will ensure that the pane fits perfectly and allows for expansion and contraction.

Place the new pane in the frame and push it into the frame using your hand. Use the chisel's point or the back of the putty knife to smudge the glazier's points as illustrated in Figure 11. When you're done, they should be level with the top edge of the pane and the shoulders of the points should be just below the rabbet's lip. groove.

Apply a small amount of glazing compound on the edges of the glass that has been made and into the rabbet grooves, to seal and protect them. Allow it to dry and cure fully.

After the glazing compound dries it's time to put in the new window sash. First, saturate the wood with a thick coat of linseed oil. This will stop the new putty drying out or cracking as it absorbs moisture. Use a brush to apply this coat, or the point of the blade. Then use the chisel that is on the back of the putty tool or the back of the handle to gently hammer the new sash or glazier's tip into the rabbet grooves. Repeat this process at intervals of 10 inches all around the frame.

Putty

A baseball thrown or a rock thrown by error, or a tree falling can cause a broken or cracked window pane. Most windows can be replaced easily by simply putting in a fresh piece. The glass is held in place using tiny metal clips known as a glazier's point, and putty, often called glazing compound. Before you install a new pane, first get rid of the old one and clean up the area with the help of a rag, an abrasive scraper that is a pull type or the wood chisel. Wear gloves and safety glasses when working. You'll need a heating gun when the window is fixed to the frame.

If you are planning to replace the original sash in the future, take care to remove the molding pieces that are used to secure the old pane. Sand the sash until it's flat and ready for new caulk. Once the sash is reinstalled then, you can apply a silicone caulk to the glass. This will ensure that it doesn't be leaking or fade over time.

Take out the glazing points in the rabbets. These are the grooves in the sash, which is where the glass is. If they're difficult to work out, try holding the hand tool, such as a heat gun to soften them first. If you're using a heating gun, be cautious not to scratch the railings or sash by using the tool too close.

Prepare a bed for your new pane after you have removed the old putty and glazing points. Roll a piece of glazing compound between your hands, and form it to be about 1/2-inch thick. Place it into the rabbets, where the glass will be placed. It is crucial that the glass sits on the putty on each side So if you have to, lightly tap the replacement glass windows into the rabbet using your thumb.

If the new pane is cracked, you can apply a silicone caulk or a glass glue made from solvents to fill in the crack before pressing it in the sash. If the crack isn't sealed, you will need to use putty to keep water out. Once the putty is dry, wipe the oily film off the glass and let it dry completely before you paint. If you paint before the putty is completely dry, it won't create a strong seal and may discolor or leak in time.

Paint

If you've experienced a broken window pane, then you may be concerned about the expense of a new one. But the truth is that replacing a single glass pane doesn't require a huge amount of money if you do it yourself. Even a double-paned window could be replaced for a fraction of the price it would cost a professional.

If you are working on a large window, make sure it is securely fastened to the frame. By using the correct tools and techniques you can make this task relatively easy and fast.

When you are ready to start, remove the old window pane. Remove the metal glazing points attached to it. They are basically tiny metal triangles that act as "nails" which hold the window in within the frame of wood. They are buried under a bead of glazing putty that transforms into a solid molded wedge that secures the window in place and hides the edges.

After removal of the old pane clean the frame and the wood. Scrape off any old paint and sand down the rabbet grooves that the glazing points were placed. They should be sanded to bare wood, so that you can paint them the same color as the rest the frame. After sanding the wood then apply a layer of flax oil. This will help to extend its life.

Next, measure the dimensions of the window opening. You will need to measure the vertical and horizontal dimensions of the entire opening, as well as the thickness. To determine the exact size of the new pane, subtract 1/8 inch from both measurements. This will also allow for expansion and contraction of the glass during seasons of changes. Take these dimensions to your local hardware or home improvement store and have cut the glass for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.