• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane can be a nuisance. This could be an opportunity to upgrade to energy-efficient windows or insulated ones, and reap benefits like increased comfort, higher resale value and lower utility costs.

You can do it yourself for a fraction of what it would cost to hire an expert. It requires the right tools and only an hour or two of your time.

Glass

Replace your old single-paned windows using tempered or insulate glass to improve the efficiency of your energy, reduce noise, and preserve the historical integrity of your old home. The procedure of replacing windows is easy and can be accomplished by anyone with basic hand tools. You'll also require a replacement double glazed window (http://work.Proh.co.Kr/bbs/board.php?bo_table=free&wr_Id=148229) window pane, glazier's tips pliers, and latex glaze putty. If necessary, you can use a heating gun to warm the old putty. Wear safety goggles and gloves prior to starting. Working with broken glass could result in serious injuries.

Remove any broken glass pieces remaining. This is best done using a pair of pliers, however, a flathead screwdriver may be used in a pinch. Then, use a wood chisel or putty knife take the remainder of the old putty from around the frame and the sash. Take your time and work slowly and be careful not to break the current window sash. It is best to do this using a sturdy ladder rather than the ground and to have someone stand below the sash to help hold it in place.

Prepare the window frame to accommodate the new pane after you have removed the old putty. Measure the width and height of the sash opening by subtracting 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be sent to a hardware or home center store to get a piece cut of glass stock to the proper size. You can also cut the glass by yourself if you have the right tools.

After installing the glass After installing the glass, apply caulking around the edge. This will make the glass weatherproof. Then, you can install a glazier's pointing on each side of the frame to hold the pane in its place. The points should not be so tight as to cause friction between the sash and the frame but they shouldn't be too loose.

Before applying the putty, knead it thoroughly until it's soft and free of lumps. Roll it into pencil-sized strips. The first strip should be glued to the frame's corner. Work from one corner to another to ensure it's even and smooth.

Glazier's Points

The glazier's points are the small triangular pieces of metal that allow glass to be secured into frames for windows without damaging or scratching the delicate surface. It's easy to learn how to use this secret tool and you can save money on the cost of an installation by a professional.

After the old putty as well as the glazier's points have been removed Clean the frame thoroughly using a utility knife to eliminate any remaining traces. Lightly sand the wood into the rabbet grooves, if necessary, to smooth rough areas. If you do sand the wood, ensure you protect it with painter's tape to avoid accidental damage.

Take measurements of the empty frame and record precise measurements. These dimensions can be taken to the hardware or home center store, and the new frame will be cut to a smaller size. This will ensure a tight fit and leave room for expansion and contraction.

Place the new pane in the frame and push firmly using your hands. Use the point of the chisel or the edge of the putty blade to tap in the glaziers' points as shown in Figure 11. After you're done, the points should be level with the top edge of the pane. the shoulders that are raised of the points should be just below the rabbet's rim groove.

Apply a small amount of glazing compound on the edges of the new glass and in the rabbet grooves to seal and protect them. Let it dry completely and cure.

When the glazing compound is dry and the glazing compound is dry, you can install the new window sash. First, coat the wood with a thick coat of linseed oil. This will prevent the new putty from soaking up the moisture and drying out and cracking with time. Apply the coating using a brush this coat, or the point of the blade. Then use the chisel that is on the back of the putty tool or the back of the handle to gently hit the new sash, or glazier's point into grooves of the rabbet. Repeat this process every 10 inches around the perimeter of the frame.

Putty

A baseball thrown or a rock thrown in error or a branch falling could result in a broken or cracked window replacement companies pane. Fortunately, the majority of windows can be easily replaced by simply putting a new piece in the right place. The glass is held into place by a small metal clip, called a glazier’s point and putty. This compound is also called glazing compound. Before you install a new pane, first remove the old one and clean up the area with a rag and a pull-type paint scraper or the wood chisel. Wear protective glasses and Replacement Double glazed window gloves while working. If the window is attached to the frame, you'll need to employ a heat gun in order to soften the adhesive prior to taking it off.

If you're planning to reinstall your original sash, remove the molding that supports the old pane. Sand the sash until it's flat and ready to receive new caulk. After the sash has been reinstalled then, you can apply a silicone caulk on the glass. This will ensure that it doesn't be leaking or fade over time.

Take the glazing points out of the rabbets, the grooves in the sash where the glass is. If they are hard to chisel, use a hand tool such as a heating gun over them to soften first. When using a heat tool, be careful to not scratch the sash's railings and sash.

After the old glaze points and putty are removed, make a bed for the new pane. Roll a rope of glazing compound between your hands, shaping it into a 1/2-inch thick. Then, push it into the rabbets, where the glass will be. It's important that the glass is positioned against the putty on each side If you have to tap it, gently press the glass into the rabbet with your thumb.

If the new pane has a crack then you can seal it with a solvent-based glass glue or silicone caulk prior to pressing it into the sash. Otherwise, you'll need to apply putty on the crack to create a tight seal and keep water out. After the putty is dry, clean the oily film off the glass with a rag and allow it to completely dry before painting. Paint before the putty has completely dried. It will not create a solid seal and may leak or discolor with time.

Paint

If you've had a broken window pane, you may be concerned about the expense of a new one. However, replacing a single glass pane doesn't require a huge amount of money If you can do it yourself. In fact, even a double-pane window can be replaced at a fraction of the cost of an expert.

If you're working with a large glass window, first make sure it is securely fixed to the frame. This task can be made relatively simple and fast with the appropriate tools and techniques.

If you're ready to begin with the removal of the old window by prying out the glazing points of metal that are attached to it. These are tiny triangles of metal which act as "nails" to hold the window within the frame. They are submerged beneath a bead or glazing putty that hardens to solid wedge that holds the frame securely in place and hides the points.

After removing the old pane, clean the frame and wood. Scrape off any old paint, and sand the rabbet grooves where the glazing points were. They should be sanded to bare wood so that you can paint them the same shade as the rest of the frame. After the sanding process, apply a coat of flax oil to the wood's surface to extend the life of the frame.

The next step is to determine the size of the window seal replacement opening. It is necessary to measure the horizontal and vertical dimensions of the entire opening, as well as the thickness. Subtract 1/8 inch from each measurement to ensure that you have the exact size for the new pane. This will also allow for expansion and contraction of the glass in times of seasonal change. Bring these measurements to the hardware or home improvement store and have a piece cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.